Correct aquarium installation is essential for the safety, performance and longevity of the aquarium, cabinet and surrounding property.
Aquariums become extremely heavy once filled. The supporting surface must safely carry the complete operating weight of the aquarium, including:
- The aquarium itself
- Water
- Substrate
- Rocks and decorations
- Filters and equipment
- Cabinet or stand
- Sump and plumbing
- Any equipment mounted on or supported by the aquarium
This guide applies to aquariums, cabinets and stands purchased from Roxy Aquarium.
Always follow the installation instructions supplied by the aquarium and cabinet manufacturer. Where manufacturer instructions differ from this guide, the manufacturer’s instructions should be followed.
Nothing in this guide excludes, restricts or modifies any rights or remedies available under the Australian Consumer Law.
1. Check the aquarium before installation
Before placing the aquarium on a stand or filling it with water, inspect it carefully in a well-lit area.
Check for:
- Cracks
- Chips
- Scratches
- Damaged edges
- Silicone separation
- Distorted or damaged framing
- Uneven base panels
- Missing components
- Transport damage
- Damage to the cabinet or stand
Remove protective wrapping carefully, but retain the packaging until the aquarium has been fully inspected.
Do not install, fill or modify an aquarium that appears cracked, chipped, structurally damaged or incorrectly manufactured.
Take clear photographs and contact Roxy Aquarium before proceeding.
2. Calculate the aquarium’s approximate operating weight
Aquarium capacity alone does not represent the total operating weight.
As a general estimate:
- One litre of freshwater weighs approximately one kilogram
- Saltwater may weigh slightly more
- Glass, substrate, rocks, equipment and the cabinet add additional weight
For example, an 84-litre aquarium may exceed 100 kilograms once the tank, water, substrate, rocks and equipment are included.
Larger aquariums can weigh several hundred kilograms or more.
Customers must consider the full operating weight—not only the aquarium’s advertised water capacity—when selecting:
- A cabinet or stand
- A floor location
- Shelving
- Benchtops
- Furniture
- Wall or floor protection
Where there is uncertainty about the floor or structure, seek advice from a suitably qualified builder, engineer or other appropriate professional before installation.
3. Use a suitable aquarium stand or cabinet
The aquarium must be installed on a stand, cabinet or supporting surface that is:
- Designed or approved for aquarium use
- Structurally capable of supporting the full operating weight
- Correctly assembled
- Stable and free from movement
- Flat and level
- Appropriate for the aquarium’s dimensions
- Resistant to deformation under load
- Positioned on a stable supporting floor
A household table, dresser, shelf, television cabinet or general-purpose furniture item may not be suitable, even where it initially appears strong enough.
Aquarium weight is continuous and concentrated over a relatively small area. General furniture may:
- Bow
- Twist
- Swell
- Separate at joins
- Collapse under prolonged loading
- Provide incomplete support to the aquarium
Where an aquarium is sold as a matching aquarium-and-cabinet set, we strongly recommend using the matched cabinet and following its assembly instructions.
4. The stand must be correctly assembled
Cabinets and stands must be assembled exactly as instructed.
Before placing the aquarium on the stand, confirm that:
- All panels are installed in the correct orientation
- Structural dividers and braces are fitted
- Fasteners are fully secured
- Dowels and locking fittings are correctly engaged
- Adjustable feet are installed and correctly positioned
- The top panel is seated properly
- The cabinet does not rock, twist or wobble
- No parts are missing
- Doors do not cause the cabinet to move out of alignment
Do not alter, remove or relocate structural panels without written manufacturer approval.
Removing a brace, divider, support rail, top panel or rear panel may weaken the cabinet.
5. The aquarium must be level
The aquarium must be level:
- From left to right
- From front to back
- Across the full supporting surface
Use a suitable spirit level to check the stand before placing the aquarium on it.
Check the level again:
- 1After the cabinet has been assembled
- 2After the cabinet is positioned
- 3After the empty aquarium is placed on the cabinet
- 4During the initial test fill
- 5After the aquarium has settled under load
A tank that is not level may place uneven stress on:
- Glass panels
- Silicone seams
- Frames
- Cabinet panels
- Plumbing and bulkheads
Do not use water level alone as the only method of determining whether the stand is correctly installed.
6. Level the stand—not the aquarium
Where levelling is required, adjustments should normally be made beneath the stand or through its manufacturer-provided adjustable feet.
Do not place makeshift materials between the aquarium and stand, including:
- Timber pieces
- Coins
- Cardboard
- Folded paper
- Tiles
- Plastic wedges
- Uneven foam strips
- Individual shims beneath one part of the aquarium
Never attempt to correct an uneven stand by supporting only one corner or section of the aquarium.
Any shims used beneath a cabinet should:
- Be suitable for the total load
- Support the relevant area correctly
- Be stable and moisture-resistant
- Be installed without twisting the cabinet
For large aquariums or significant floor irregularities, obtain professional installation advice.
7. Full-base and perimeter-supported aquariums
Aquariums are constructed using different support designs.
Full-base or rimless aquariums
A full-base or rimless aquarium may require:
- Continuous support beneath the entire base
- A manufacturer-approved aquarium mat
- A completely flat supporting panel
- No gaps, raised fasteners or surface debris
Framed or floating-base aquariums
Some framed aquariums are designed to be supported around their perimeter rather than across the entire glass base.
These aquariums may:
- Have a raised bottom panel
- Use a plastic or metal frame
- Require support only under the frame
- Specifically prohibit an additional foam mat
Do not assume that every aquarium needs the same support method.
Follow the instructions for the specific aquarium model.
8. When is a foam mat required?
Use an aquarium foam or levelling mat where:
- It is supplied with the aquarium
- It is permanently attached by the manufacturer
- The manufacturer’s instructions require it
- The aquarium is designed for full-base support and the manufacturer approves its use
- Roxy Aquarium has confirmed that the specific model requires one
A suitable mat may help accommodate very small surface imperfections and provide continuous contact beneath a compatible aquarium.
A foam mat does not:
- Reduce the aquarium’s total weight
- Reduce the load carried by the stand or floor
- Correct a structurally unsuitable cabinet
- Correct a significantly uneven surface
- Make a weak stand safe
- Compensate for a twisted cabinet
- Protect against improper handling or impact
- Replace correct levelling
The stand and floor must still support the complete operating weight.
9. When should a foam mat not be used?
Do not place a foam mat beneath an aquarium where:
- The manufacturer says not to use one
- The aquarium has a raised or floating base
- The framed design requires perimeter support
- The mat would press against unsupported bottom glass
- The aquarium already has a permanently attached mat
- The material is too soft, uneven or compressible
- The mat does not cover the required area
- The mat causes the aquarium to become unstable
- The mat interferes with the frame or cabinet design
Using an inappropriate mat can change how the aquarium is supported.
When uncertain, contact Roxy Aquarium with:
- The aquarium model
- Tank dimensions
- Photographs of the base
- Photographs of the stand
- The proposed mat type and thickness
Do not proceed until compatibility has been confirmed.
10. Foam mat requirements
Where a mat is required, it should:
- Be designed or approved for aquarium use
- Be suitable for the aquarium’s dimensions
- Cover the required supporting footprint
- Be uniform in thickness
- Be clean and undamaged
- Lie completely flat
- Have no folds, overlaps or raised edges
- Have no debris trapped underneath
- Be installed according to the manufacturer’s directions
Do not use:
- Carpet underlay
- Folded towels
- Packaging foam
- Polystyrene beads
- Yoga mats
- Sponge offcuts
- Uneven or joined pieces
- Materials that degrade when wet
- Excessively thick or soft foam
Do not stack multiple mats unless the manufacturer specifically permits it.
11. Clean the supporting surface
Before placing the aquarium on the stand:
- 1Clean the cabinet top.
- 2Remove all dust, grit, screws and packaging.
- 3Check for raised fasteners or uneven joins.
- 4Run your hand carefully across the surface.
- 5Confirm that the surface is flat and undamaged.
- 6Install the approved mat, where required.
- 7Lift the aquarium into position without dragging it.
Even a small piece of hard debris trapped beneath a full-base aquarium may create a pressure point.
Never slide or drag an aquarium across a cabinet or foam mat.
12. Aquarium overhang is not permitted
The aquarium must sit completely within the supporting footprint required by its design.
There must be no unsupported overhang at:
- The front
- The rear
- Either side
- Any corner
Do not place a larger aquarium on a smaller cabinet.
Do not assume that a small amount of overhang is acceptable.
The cabinet should match the aquarium’s dimensions and required support pattern.
13. Positioning the aquarium
Choose a location that is:
- Indoors, unless the aquarium is specifically designed for outdoor use
- On a suitable and stable floor
- Away from direct sunlight where practical
- Away from heaters and fireplaces
- Away from air-conditioning drafts
- Protected from impact and heavy traffic
- Accessible for maintenance
- Close to suitable electrical outlets
- Away from areas where water damage could create a serious hazard
Consider access for:
- Filters
- Hoses
- Plumbing
- Power cables
- Maintenance equipment
- Lid removal
- Lighting
- Water changes
Leave sufficient clearance around the aquarium and cabinet.
14. Floor suitability
The floor must safely support the aquarium’s complete operating weight.
Consider:
- Aquarium size
- Cabinet footprint
- Concentrated point loads from cabinet feet
- Timber floor movement
- Upper-storey installation
- Uneven tiles
- Soft flooring
- Carpet compression
- Underfloor heating
- Existing structural damage
Roxy Aquarium cannot assess the structural capacity of a customer’s building based only on the aquarium’s litre capacity.
For large aquariums, upper levels, suspended timber floors or uncertain structures, obtain professional advice before installation.
15. Installation on carpet
Carpet may compress unevenly once the aquarium is filled.
This can cause:
- Cabinet movement
- Difficulty levelling the stand
- Doors becoming misaligned
- Uneven loading
- Moisture becoming trapped beneath the cabinet
Where installation on carpet cannot be avoided:
- Confirm that the floor beneath it is suitable
- Ensure the cabinet remains stable
- Check that all feet are supported
- Recheck level as the carpet settles
- Follow the cabinet manufacturer’s requirements
Do not remove structural feet or alter the cabinet solely to compensate for carpet.
16. Installation on tiles
Tiles can appear level while individual tiles or grout lines create uneven contact.
Before installation:
- Check for cracked or loose tiles
- Check for raised edges
- Check for significant grout-line variation
- Confirm all cabinet feet are supported
- Confirm the cabinet does not rock
- Level the cabinet appropriately
Do not place hard wedges between the aquarium and cabinet to compensate for uneven tiles.
17. Protect the cabinet from water
Most timber, particleboard, MDF and laminated aquarium cabinets are moisture-resistant rather than waterproof.
Immediately wipe away water from:
- Water changes
- Condensation
- Filter maintenance
- Hose connections
- Sump areas
- Spills
- Leaks
- Wet equipment
- Dripping lids
Do not allow water to:
- Pool on the cabinet top
- Run behind the aquarium
- Enter unsealed joins
- Sit around cabinet feet
- Remain inside the cabinet
- Soak into cut-outs or drilled holes
Repeated water exposure may cause:
- Swelling
- Delamination
- Warping
- Mould
- Door misalignment
- Loss of structural strength
A drip tray or suitable cabinet liner may be used where it does not interfere with ventilation, electrical safety or structural components.
18. Plumbing, hoses and filtration equipment
Filters, sumps and plumbing must be installed according to their manufacturer’s instructions.
Confirm that:
- Hoses are not kinked
- Fittings are secure
- Bulkheads are installed correctly
- Plumbing is not under sideways stress
- Valves remain accessible
- Hoses cannot pull on the glass
- Equipment is properly supported
- The cabinet has adequate ventilation
- There is enough clearance for maintenance
Do not use the aquarium glass, brace, lid or cabinet panel to support equipment unless the aquarium and equipment manufacturers permit it.
19. Equipment hung from aquarium glass
Some filters, lights, brackets and accessories are designed to hang from the aquarium edge.
Before attaching equipment, confirm:
- The aquarium manufacturer permits it
- The bracket is compatible with the glass thickness
- The bracket fits the aquarium’s edge design
- The weight is within the bracket’s rating
- The equipment does not load or twist the glass
- The bracket does not damage silicone or framing
- The equipment clears lids, braces and cables
- The installation follows the equipment manufacturer’s instructions
Do not clamp equipment excessively tightly against the glass.
Do not attach unsuitable shelves, brackets or heavy equipment to an aquarium panel.
20. Modifying the aquarium or cabinet
Do not modify the aquarium or cabinet without prior written approval from the relevant manufacturer.
Modifications include:
- Drilling glass
- Cutting glass
- Removing braces
- Removing frames
- Cutting structural cabinet panels
- Relocating cabinet supports
- Installing oversized equipment
- Attaching heavy brackets
- Altering plumbing holes
- Removing the cabinet top
- Changing adjustable feet
- Adding unsupported shelves
Structural alterations may affect safety and may be relevant when assessing a warranty claim.
Any rights available under the Australian Consumer Law continue to apply.
21. Electrical safety
Aquarium equipment combines electricity and water and must be installed carefully.
Customers should:
- Follow all equipment instructions
- Use appropriate electrical outlets
- Keep plugs and power boards away from water
- Create drip loops in power cords
- Avoid overloading outlets
- Replace damaged cords or plugs
- Keep electrical equipment ventilated
- Turn off and isolate equipment before maintenance
- Use a licensed electrician where electrical work is required
Do not operate electrical aquarium equipment that is wet, damaged, cracked or behaving abnormally.
Roxy Aquarium does not perform licensed electrical work unless specifically arranged through an appropriately qualified provider.
22. Do not lift or move a filled aquarium
Aquariums must not be lifted, dragged, rotated or moved while containing:
- Water
- Substrate
- Rocks
- Decorations
- Livestock
- Equipment
Before moving an aquarium:
- 1Disconnect electrical equipment safely.
- 2Remove livestock appropriately.
- 3Drain all water.
- 4Remove rocks, substrate and decorations where required.
- 5Remove plumbing and equipment that may apply force to the tank.
- 6Use enough people and appropriate lifting equipment.
- 7Lift the tank evenly from supported areas.
Moving a partially filled aquarium can place severe stress on the glass and silicone seams.
23. Initial test filling
Before completing the aquascape or introducing livestock, perform an initial test where practical.
Recommended process:
- 1Confirm the cabinet is assembled and level.
- 2Inspect the aquarium and silicone.
- 3Confirm all plumbing and bulkheads are secure.
- 4Ensure the correct support mat is installed where required.
- 5Add a small amount of water.
- 6Check the aquarium and cabinet for movement.
- 7Continue filling gradually.
- 8Inspect all seams, plumbing and connections.
- 9Recheck the aquarium’s level.
- 10Monitor the setup before adding livestock.
A test fill should be performed in a location where a possible leak can be safely detected and managed.
Do not leave an unfamiliar setup unattended during the initial fill.
24. Adding rocks and heavy decorations
Heavy rocks and decorations must be placed carefully.
Customers should:
- Avoid dropping objects onto the glass
- Avoid concentrating excessive weight on one point
- Ensure rock structures are stable
- Prevent rocks from falling against glass panels
- Use suitable base protection where appropriate
- Keep heavy decorations away from unsupported edges
- Consider displacement when calculating water volume
Large rocks should not rely on loose substrate alone for stability.
Aquascapes should be designed so that digging fish cannot undermine heavy structures.
25. After installation
Continue to monitor the aquarium and cabinet after setup.
Check regularly for:
- Changes in level
- Cabinet swelling
- Door misalignment
- Water pooling
- Salt creep
- Hose movement
- Plumbing leaks
- Silicone changes
- Unusual sounds
- Frame separation
- Floor movement
- Cabinet wobble
Stop using the aquarium and contact Roxy Aquarium promptly if you observe:
- Cracking sounds
- A visible crack
- Active leakage
- Rapid silicone separation
- Significant cabinet movement
- Structural swelling
- A cabinet panel separating
- Plumbing failure that cannot be isolated
Where safe, disconnect electrical equipment and protect people and property from water.
26. Installation evidence
For aquarium, cabinet or leakage claims, we may reasonably request:
- Proof of purchase
- Aquarium model and dimensions
- Photographs of the full installation
- Photographs showing the stand and floor
- Spirit-level photographs
- Photographs of the aquarium base
- Photographs of any support mat
- Cabinet assembly photographs
- Images of the affected area
- Video showing the leak or movement
- Details of modifications
- Details of plumbing and attached equipment
- Installer information, where applicable
This information helps determine:
- What occurred
- Whether the aquarium was correctly supported
- Whether a component has failed
- Whether repair, replacement or another remedy is appropriate
A claim will not be refused solely because every requested item is unavailable where the issue can otherwise be reasonably established.
27. Customer-installed and third-party-installed aquariums
Where the customer or an independent third party installs the aquarium, they are responsible for carrying out the installation with appropriate care and skill.
Roxy Aquarium is not responsible for installation work performed independently by:
- The customer
- A delivery contractor not engaged to install the aquarium
- A handyman
- A cabinetmaker
- A plumber
- An electrician
- Another aquarium installer
However, this does not remove any rights relating to a defect in goods supplied by Roxy Aquarium or any installation service supplied directly by Roxy Aquarium.
Where installation is purchased from Roxy Aquarium, the service will be assessed separately under applicable service guarantees.
28. Warranty assessment
Incorrect installation, unsuitable support, unauthorised modification, impact, twisting, cabinet water damage or misuse may be relevant when determining the cause of a failure and assessing a manufacturer or voluntary warranty claim.
Examples may include:
- Installing the aquarium on an unsuitable stand
- Unsupported overhang
- Failing to use a required manufacturer-approved mat
- Using a mat where the manufacturer prohibits it
- Filling an aquarium on an uneven or twisted cabinet
- Moving an aquarium while partially filled
- Drilling or modifying the tank
- Removing structural cabinet components
- Allowing prolonged water ingress into the cabinet
- Damage caused by impact or dropped decorations
A warranty condition does not remove rights that may independently apply under the Australian Consumer Law.
The cause of the problem and the circumstances of the installation will be assessed individually.
29. Australian Consumer Law
Products and services supplied by Roxy Aquarium come with consumer guarantees that cannot be excluded under the Australian Consumer Law.
Products must be:
- Of acceptable quality
- Safe
- Durable
- Free from defects
- Fit for any disclosed purpose
- Consistent with their description
Services must be provided:
- With due care and skill
- Fit for their disclosed purpose
- Within a reasonable time where no timeframe was agreed
Where a product or service does not meet an applicable consumer guarantee, the customer may be entitled to a remedy.
The appropriate remedy depends on the circumstances and whether the failure is major or minor.
Nothing in this guide limits those rights.
30. Installation checklist
Before filling your aquarium, confirm:
- [ ] The aquarium has been inspected for damage
- [ ] The stand is suitable for the aquarium
- [ ] The stand is correctly assembled
- [ ] The floor can support the full operating weight
- [ ] The cabinet is stable and does not wobble
- [ ] The cabinet is level from front to back
- [ ] The cabinet is level from side to side
- [ ] The aquarium has no unsupported overhang
- [ ] The correct support method is being used
- [ ] A foam mat is installed only where required or approved
- [ ] The supporting surface is clean and free from debris
- [ ] Plumbing is secure and correctly supported
- [ ] Hanging equipment is compatible with the aquarium
- [ ] Electrical cables have drip loops
- [ ] Structural components have not been modified
- [ ] Heavy rocks and decorations are safely supported
- [ ] The aquarium will be test-filled before livestock is added
- [ ] Photographs of the completed installation have been retained
Contact us before filling the aquarium if you are uncertain about:
- Stand compatibility
- Foam mat requirements
- Aquarium support
- Cabinet assembly
- Equipment brackets
- Glass thickness
- Plumbing
- Installation instructions
- A visible defect or damage
Please provide the aquarium model, dimensions and clear photographs so we can assist accurately.
Email: info@roxyaquarium.com.au
Phone: 03 8000 8723
Address: 1 Fleet Street, Somerton, VIC 3062
Do not fill or continue using an aquarium where there is concern about its structural safety.